node route size mismatch
Moderator: Defcon moderators
node route size mismatch
I keep getting thise rror when I try to load spacemonkey's australia map and my new map im workig on. Any one know how to fix this?
Thanks!
Thanks!
- shinygerbil
- level5
- Posts: 4667
- Joined: Wed Dec 22, 2004 10:14 pm
- Location: Out, finding my own food. Also, doing the shinyBonsai Manoeuvre(tm)
- Contact:
i can play australia fine, but i have the same problem on my MOD. Here is what my travel nodes and sailable files look like, as well as the map in question:
This is the map i'm working on...
This is the sailable region of the map
These are the travel nodes
Mix of both files above to show that all the nodes are in the water, and each node connected to at least one other.
This is the map i'm working on...
This is the sailable region of the map
These are the travel nodes
Mix of both files above to show that all the nodes are in the water, and each node connected to at least one other.
I reduced it to 21 nodes and it still gives me the error. it's frustrating!
i think it has to do with the fact the original file was 800x400 and i made it 512x284 to match my world map. seeing how like, how the hell would i know where to put the dots in the 800x400 map when the rest of the bmps are smaller than that?
i think it has to do with the fact the original file was 800x400 and i made it 512x284 to match my world map. seeing how like, how the hell would i know where to put the dots in the 800x400 map when the rest of the bmps are smaller than that?
- shinygerbil
- level5
- Posts: 4667
- Joined: Wed Dec 22, 2004 10:14 pm
- Location: Out, finding my own food. Also, doing the shinyBonsai Manoeuvre(tm)
- Contact:
You will receive this error if any one node can't sail directly to at least one other node.
Basically, if you can't draw a straight line between 2 of your nodes on the sailable.bmp without crossing a non-sailable area, you cant sail between them. If any of your nodes are issolated in this way, you'll get the error.
I'd try drawing lines between all of your points. If any of them even come close to overlapping a non-sailable area, try nudging them out of the way slightly.
Basically, if you can't draw a straight line between 2 of your nodes on the sailable.bmp without crossing a non-sailable area, you cant sail between them. If any of your nodes are issolated in this way, you'll get the error.
I'd try drawing lines between all of your points. If any of them even come close to overlapping a non-sailable area, try nudging them out of the way slightly.
Ok, i finally got it to accept my travel nodes! But, when i test the map vs a CPU, it crashes still after 30-60 seconds into the match. USually when it's 4:30 till DEFCON 4. It doen't matter what i'm doing at this time...
Is this because I have no information in the ai_markers.bmp? I have no idea how the ai markers work and there's no guides anywhere about that file. Right now, my ai_markers.bmp is a blank black map.
EDIT: I just planted random green and red dots at the various areas where countries can deploy sea units and it works without crashing now. =D
Is this because I have no information in the ai_markers.bmp? I have no idea how the ai markers work and there's no guides anywhere about that file. Right now, my ai_markers.bmp is a blank black map.
EDIT: I just planted random green and red dots at the various areas where countries can deploy sea units and it works without crashing now. =D
- Spacemonkey
- level4
- Posts: 609
- Joined: Thu Oct 05, 2006 1:31 am
- Location: Auckland, New Zealand
Re: node route size mismatch
Gein wrote:I keep getting thise rror when I try to load spacemonkey's australia map and my new map im workig on. Any one know how to fix this?
Thanks!
Thanks for pointing that out, I havn't had that error myself, but i'll double check the node map tonite.
Who is online
Users browsing this forum: No registered users and 12 guests